IP Waterproof Test Equipments

The JL-X includes the following water proof IP codes: IPX1, IPX2, IPX3, IPX4, IPX5, IPX6, IPX7 and IPX8 (Refer to page 51 of IEC 60529). It is widely used in the authentication test organization for the products such as electrical & electronic products, LED luminaires as well as in the relevant quality control department for the waterproof detection of the enclosures protection grades.

Standard:
IEC 60529:1989 +A1:1999 +A2：2013  “Degrees of protection provided by enclosures(IP Code)”
IEC 60598 “Luminaires – Part 1: General requirements and tests”
IEC 60335 “Household and similar electrical appliances – Safety – Part 1: General requirements”
IEC 60034-5 “Rotating electrical machines – Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) – Classification”
 GB 7000.1 “Luminaires-Part 1：General requirements and tests”

The whole JL-X waterproof test system includes:
• Drip Box (JL-12): The drip box meets the test requirements of IPX1 and IPX2 in Clause 14.2.1-14.2.2 and Figure 3 of IEC 60529:1989 +A1:1999 +A2：2013 . The drip box size is 800x800x45mm (LxWxH). The diameter of drip hole is 0.4mm. The distance between drip holes is 20mm. It can test samples over 150kg.

JL-12 Drip Box, IEC 60529 Figure 3

• Swing Pipe Water Spray Test Equipment (JL-34): It meets the test requirements of IPX3 and IPX4 in Clause 14.2.3-14.2.4 and Figure 4 of IEC 60529:1989 +A1:1999 +A2：2013 . The radius of oscillating tube is 1meter (Any other size is also available). The internal diameter of the tube is 15mm. The sample turntable diameter is 1000mm (Other sizes are optional according to the diameter of the oscillating tube), and the height is adjustable. It includes a water tank. The rotation speed is 1~5rpm which can be set and controlled by PLC panel.

JL-34 Swing Pipe Water Spray Test Equipment, IEC 60529 Figure 4 

• Spraying Nozzle and Splashing Water Hand held Test Device (JL-34S): It meets the test requirements of IPX3 and IPX4 in Clause 14.2.3-14.2.4 and Figure 5 of IEC 60529:1989 +A1:1999 +A2：2013
• Water pressure regulation requirement: The water pressure is adjusted to achieve the specified flow rate, and the required pressure range is 50 kPa to 150 kPa.
• Test duration requirement: The test duration is 1 minute per square meter of the calculated surface area of ​​the shell (excluding any mounting surface), and the minimum test time is 5 minutes.
• The JL-34S includes the following: a pressure gauge, an 8m long water pipe and a Sprinkler with a 5mm Spray Nozzel.

JL-34S Spraying Nozzle and Splashing Water Hand held Test Device, IEC 60529 Figure 5

• Waterproof Jet Test Device (JL-56): It meets the test requirements of IPX5 and IPX6 in Clause 14.2.5-14.2.6 and Figure 6 of IEC 60529:1989 +A1:1999 +A2：2013. With a 780*580*1100mm size water tank, the nozzle diameter is ф6.3mm (IPX5 waterproof test ) and ф12.5mm (IPX6 waterproof test). The water flow is 12.5 ±0.625L/min for IPX5 and 100 ±5L/min for IPX6

JL-56 Waterproof Jet Test Device , IEC 60529 Figure 6

• Immersion tank Waterproof test Device (JL-7): It meets the test requirements of IPX7 in Clause 14.2.7 of IEC 60529:1989 +A1:1999 +A2：2013. The water tank size is 1000x1000x1200mm (Other sizes are optional). It can test samples up to 120kg. 

The test is made by completely immersing the enclosure in water in its service position as specified by the manufacturer so that the following conditions are satisfied:
a) the lowest point of enclosures with a height less than 850 mm is located 1 000 mm below the surface of the water;
b) the highest point of enclosures with a height equal to or greater than 850 mm is located 150 mm below the surface of the water;
c) the duration of the test is 30 min;
d) the water temperature does not differ from that of the equipment by more than 5K. However, a modified requirement may be specified in the relevant product standard if the tests are to be made when the equipment is energized and/or its parts in motion.

JL-7 Immersion tank Waterproof test Device

• Immersion tank Waterproof test Device (JL-8): It meets the test requirements of IPX8 in Clause 14.2.8 of IEC 60529:1989 +A1:1999 +A2：2013.. It can simulate a water depth of 0~50m. The water immersion tank diameter is 600mm and the height is 1200mm. The compressive stress is 10 atmospheres or design according to customer‘s request.

JL-8 Immersion tank Waterproof test Device

Optional suggestions: When using JL-8 Immersion tank Waterproof test Device , it is necessary to choose a LISUN LS-EU800W2-55L air compressor (power 800W*2, capacity 55L, speed 1380r/min, pressure 0.7Mpa, flow 120L/m in, 220~240V/50Hz) or LS-US800W2-55L air compressor (power 800W*2, capacity 55L, speed 1380r/min, pressure 0.7Mpa, flow 120L/min, 110~120V/60Hz).

LS-EU800W2-55L Air Compressor

LISUN JL-12 IP Waterproof Test Equipments – After-sales Frequently Asked Questions (FAQ)
LISUN JL-12 IP Waterproof Test Equipments were in the market for more than 10 years, LISUN engineers service team already summary the most of the After Sales Questions and Answers in the above link. Please read it carefuly, you can solve the most of the problems by yourself if you have some questions while using the instruments. LISUN will be continue to update this pages and more FAQ can be found in this topic link. 

LISUN JL-34 IP Waterproof Test Equipments – After-sales Frequently Asked Questions (FAQ)
LISUN JL-34 IP Waterproof Test Equipments were in the market for more than 10 years, LISUN engineers service team already summary the most of the After Sales Questions and Answers in the above link. Please read it carefuly, you can solve the most of the problems by yourself if you have some questions while using the instruments. LISUN will be continue to update this pages and more FAQ can be found in this topic link. 

LISUN JL-56 IP Waterproof Test Equipments – After-sales Frequently Asked Questions (FAQ)
LISUN JL-56 IP Waterproof Test Equipments were in the market for more than 10 years, LISUN engineers service team already summary the most of the After Sales Questions and Answers in the above link. Please read it carefuly, you can solve the most of the problems by yourself if you have some questions while using the instruments. LISUN will be continue to update this pages and more FAQ can be found in this topic link. 

LISUN JL-8 IP Waterproof Test Equipments – After-sales Frequently Asked Questions (FAQ)
LISUN JL-8 IP Waterproof Test Equipments were in the market for more than 10 years, LISUN engineers service team already summary the most of the After Sales Questions and Answers in the above link. Please read it carefuly, you can solve the most of the problems by yourself if you have some questions while using the instruments. LISUN will be continue to update this pages and more FAQ can be found in this topic link. 

Lanthy Mcc

2022-01-24

Our company just ordered some instruments from them, due to COVID-19 and their engineer can't visit us to install, thanks to Lisun's perfect videos and we can easy to install, calibrate and testing by ourselves successfully.

Waterproof Test for IPX1 and IPX2: Drip Box (JL-12) - Operation Vedio

JL-34 IPX3 IPX4 Waterproof Test - Operation Vedio

Waterproof Test for IPX5 and IPX6: Waterproof Jet Test Device (JL-56) - Operation Vedio

Waterproof Test for IPX8: Immersion tank Waterproof test Device (JL-8) - Operation Vedio