Why salt spray testing is important for solar lights outdoor

The salt spray test standard specifies the salt spray test conditions, such as temperature, humidity, sodium chloride solution concentration and pH value, and also puts forward technical requirements for the performance of the salt spray test chamber. The salt spray test standard adopted for the same product shall be selected according to the characteristics of salt spray test, corrosion rate of metal and sensitivity to salt spray.

Salt spray test standards are as follows:
GB / T2423.17-1993 《Basic environmental test procedures for electrical and electronic products Test Ka: salt spray test method》;
GB / T2423.18-2000 《Environmental testing of electrical and electronic products Part 2: Tests Test Kb: salt spray, alternating (sodium chloride solution)》;
GB5938-86 《Test method for corrosion resistance of metal coating and chemical treatment layer of light industrial products》;
GB / T1771-91 《Paints and varnishes Determination of resistance to neutral salt spray》.

Salt spray test rating method:
1. The rating judgment method divides the percentage of the ratio of corrosion area to total area into several levels according to a certain method, and takes a certain level as the basis for qualification judgment, which is suitable for the evaluation of flat plate samples.
2. The weighing judgment method evaluates the corrosion resistance quality of samples by calculating the weight (or weight gain) of corrosion loss through the weight change of samples before and after corrosion test. It is suitable for evaluating the corrosion resistance quality of a certain metal.
3. The method of determining the presence of corrosive substances is a qualitative method, which judges the samples based on whether the products have corrosion after the salt spray corrosion test. This method is mostly adopted.
4. The statistical analysis method of corrosion data is mainly used to analyze and count corrosion conditions, rather than specifically used for the quality judgment of a specific product.

The artificial simulated salt spray environment test is to use a test equipment “salt spray test chamber” with a certain volume space to assess the quality of the product’s salt spray corrosion resistance performance by artificial methods in its volume space. The salt concentration of chloride in the artificial salt spray environment is several times or several times higher than that in the natural environment. This greatly improves the corrosion degree and shortens the time to get the results of the salt spray corrosion test of products.

The artificial salt spray test also includes:neutral salt spray test, acetate spray test, copper salt accelerated acetate spray test and alternating salt spray test:
1. Neutral salt spray test (NSS test) is an accelerated corrosion test method that appeared first and is widely used in the field. A solution for spray was prepared by using a 5% sodium chloride saline solution and adjusting the pH value to neutral (6-7). The test temperature is 35 ℃, and the sedimentation rate of salt spray is required to be 1-2ml / 80cm 2. H.
2. Acetate spray test (ASS test) is developed from neutral salt spray test. By adding some glacial acetic acid to the 5% sodium chloride solution, the pH value of the solution is reduced to about 3 to become acidic, and the salt mist formed is also changed from neutral to acidic. The corrosion rate of acetate mist is about 3 times faster than that of neutral.
3. Copper salt accelerated acetate spray test (CASS test) is a rapid salt spray corrosion test developed recently from abroad. The test temperature needs to be 50 ℃, and a small amount of copper salt copper chloride is added to the salt solution to strongly induce corrosion. Its corrosion rate is about 8 times that of neutral test.
4. Alternating salt spray test is also called comprehensive salt spray test, which is composed of neutral salt spray test and constant wet heat test. It is mainly used for cavity type complete machine products. Through the penetration of the wet environment, salt spray corrosion occurs not only on the product surface but also inside the product. The alternating salt spray test alternates the products under salt spray and wet and hot environmental conditions, and finally evaluates whether the electrical performance and mechanical energy of the whole product have changed.

Therefore, salt spray testing is important for solar lights outdoor. LISUN lauched Salt Spray Test Chamber | Salt Fog Test | ASTM B117 Salt Spray ChamberSalt Spray Test Chamber is applicable to the salt spray corrosive test for the protection layer of components, parts, electronic and electrical parts and metal materials and industrial products. The salt fog test chamber meets the following standards: IEC60068-2-11 (GB/T2423.17), GB/T10125, GB/T1771, ISO9227, ASTM-B117, GB/T2423-18, QBT3826, QBT3827, IEC 60068-2-52, ASTM-B368, MIL-STD-202, EIA-364-26, GJB150, DIN50021-75, ISO3768, 3769, 3770; CNS 3627, 3885, 4159, 7669 etc.

YWX/Q-150X series Composite Salt Spray Test Machine fullly compliance with GB/T 2423. 18, GB/T-10125, IEC 60068-2-11, GMW 14872, TCSAE 71, VCS 1027_1449, PV 1210,etc standards requirements. It do measurement through simulating conditions that are more commonly encountered in the natural environment such as  salt spray, hot air drying, humidity, low temperature combined and loop in any order. It is widely used to test items used in drastically changing environments, such as automobile parts, aviation equipment, building materials, coating, electric and electrical machinery so on.

Lisun Instruments Limited was found by LISUN GROUP in 2003. LISUN quality system has been strictly certified by ISO9001:2015. As a CIE Membership, LISUN products are designed based on CIE, IEC and other international or national standards. All products passed CE certificate and authenticated by the third party lab.

Our main products are Goniophotometer, Integrating Sphere, Spectroradiometer, Surge Generator, ESD Simulator Guns, EMI Receiver, EMC Test Equipment, Electrical Safety Tester, Environmental Chamber, Temperature Chamber, Climate Chamber, Thermal Chamber, Salt Spray Test, Dust Test Chamber, Waterproof Test, RoHS Test (EDXRF), Glow Wire Test and Needle Flame Test.

Please feel free to contact us if you need any support.
Tech Dep: Service@Lisungroup.com, Cell/WhatsApp:+8615317907381
Sales Dep: Sales@Lisungroup.com, Cell/WhatsApp:+8618117273997

Tags：YWX/Q-010 , YWX/Q-010X